Walking your house: what to write down before you fix anything
Find the three shutoffs, label them, and record what every major system is before you decide what to do about any of it. The list you make here is deliberately unsorted.
- Start here: the essentials
- 1. The walk, and why it comes before the fixing
- 2. The three shutoffs
- 3. Data plates, and how to read an install date
- 4. The walk outside
- 5. The walk inside
- 6. What came with the house
- 7. What you do not open
- 8. See it
- 9. Practice
- 10. Your house
- 11. Check your work
- 12. Knowledge check and scenario
Start here Essentials
At minimum this chapter asks for two hours and a notebook. The serial-number decoding, the permit search and the question of what a paid inspection buys are all Go deeper.
- Find and label the water main. Then turn it off once, while nothing is wrong, and turn it back on (the three shutoffs).
- Find the electric panel and the fuel shutoff, and label both. Label the panel's main breaker from outside the cover (the three shutoffs).
- Write the make, model, serial and install date of the heating equipment and the water heater on the systems sheet, or the word unknown (data plates).
- Look under every sink and at the water heater's base and write down anything wet, stained or corroded (the walk inside).
Minimum time: about two hours. Done when: every shutoff you found carries a label with today's date on the shutoffs sheet, and the systems sheet has a row for the heating equipment and the water heater.
1. The walk, and why it comes before the fixing Understand
A house tells you most of what it needs if you walk around it with a notebook once. Not all of it: a walk finds what is visible, and a great deal of a house is not. But the visible part is where the cheap decisions live, and it is where almost every plan has to start, because a plan for a house you have not looked at is a plan for a generic house.
The habit this chapter builds is narrow and a little unnatural. You are going to write things down and not act on them. You will find a stained cabinet floor under the kitchen sink and not go to the hardware store. You will see that the gutter above the porch is loose and not get a ladder. You will note that the furnace has no sticker on it and not call anybody. Everything goes on one list, unsorted, and the sorting happens in The priority rule.
There are two reasons to split it that way. The first is that sorting while you walk means sorting against whatever you happened to notice first, and the thing you notice first in a house is usually the thing that looks worst, which is tier 5 almost by definition. Peeling paint is visible from the street. A downspout discharging four inches from the foundation is not, and it is the one doing damage. Convention Walking first and ranking second is this manual's method rather than a published procedure, and the reason for it is that order.
The second reason is that a walk interrupted by errands takes a weekend instead of two hours, and most people do not finish it. The list is the output. A finished list of thirty items you have not acted on is worth more than four items fixed and twenty-six never seen.
One thing does get acted on during the walk, and it is the shutoffs, because the whole point of a shutoff is that you find it before you need it.
2. The three shutoffs
Three controls stop the three things that can damage a house quickly from the inside: water, fuel and electricity. Every householder should be able to reach all three in the dark, and so should anybody else who stays in the place. Weekend Home Fixer's home maintenance course opens with the same three, which is one practitioner agreeing about the placement rather than a standard, but the logic stands on its own: a burst supply line in a finished basement is a question of minutes.
The water main
The main shutoff is on the house side of the water meter, usually where the service line comes through the foundation wall or the slab: in a basement, in a crawl space, in a utility closet, in a garage, or in a box in the yard with a lid marked for water. On a slab-on-grade house it is often in the garage or in an exterior wall box. It is a round wheel (a gate valve) or a lever (a ball valve). A lever that sits in line with the pipe is open; a lever across the pipe is closed. A wheel closes clockwise.
Turn it off once, now, while nothing is wrong. Then open a faucet on the lowest floor and confirm the flow dies. Then turn it back on slowly and watch for drips at the valve body. Test it This is the whole point of the exercise: a valve nobody has turned in fifteen years sometimes will not turn, and sometimes weeps at the stem afterward. Finding that out on a Tuesday afternoon is a plumbing appointment. Finding it out while water is coming through the ceiling is a different day.
If the valve will not turn by hand, stop. Do not put a wrench on it and lean. That is the row on your list that says "main shutoff seized, plumber", and it belongs near the top of it.
The fuel shutoff
If anything in the house burns natural gas or propane, there is a shutoff where the fuel enters, usually at the meter outside or at the tank, and often a separate valve at each appliance. Find them, label them, and leave them alone. Ask the authority Whether and when a householder should close a gas valve is a question for your gas utility, which usually publishes an answer and a 24-hour number; this manual does not give gas instructions. What it says is: know where the valve is, know the utility's number, and if you smell gas, leave the building first and call from outside.
The electric panel
The panel is a gray metal box, indoors or out, with a hinged door. Open the door. Do not remove the cover behind it, which is the panel's dead front and the only thing between you and the service conductors. Behind the door you will find the main breaker, usually the largest one at the top, stamped with the service size in amps: 100, 150 and 200 are common. Write that number down. Label the main, and if the branch circuit labels are blank or wrong, that is a row on your list rather than a job for today.
The panel cover stays on. Everything this manual asks you to do with a panel is done with the door open and the cover in place. Changing a breaker, adding a circuit, or working behind the cover is a licensed electrician's work, and the who-to-call table says so for every job of that kind.
Label all three with something that survives a damp basement: a luggage tag, a wrap of tape and a marker, a printed label. Write the date you tested it. The shutoffs sheet holds the same information in a form you can print and leave in a kitchen drawer, which is where the person house-sitting for you will look.
3. Data plates, and how to read an install date
A data plate is the metal or foil label a manufacturer puts on equipment, carrying the make, the model number, the serial number and usually the electrical or fuel ratings. It is the single most useful object in a house for planning, because every later question (what does it cost to replace, is it under recall, what filter does it take, how old is it) is answered from it.
Where to look, by machine:
| Equipment | Where the plate usually is | What to copy |
|---|---|---|
| Gas or electric furnace | Inside the upper access door, or on the side of the cabinet | Make, model, serial, input rating |
| Air conditioner or heat pump | On the outdoor unit's side, near the refrigerant lines | Make, model, serial, tonnage if shown |
| Boiler | On the front or side jacket | Make, model, serial, input rating |
| Water heater | On the front of the tank jacket, under the brand label | Make, model, serial, capacity, fuel |
| Washer, dryer, dishwasher | Inside the door frame, behind a drawer panel, or on the back | Make, model, serial |
| Refrigerator | Inside, on a side wall or above the crisper drawers | Make, model, serial |
Photograph each plate with a phone before you copy it, holding the phone square to the label so the characters are readable. Plates fade, and a photograph taken today is legible in eight years when the embossed one is not. Then type the numbers onto the systems sheet, because a photograph in a phone is not a record you can search, sort or print.
Four ways to establish an install date
In rough order of how much weight to give them:
- An installer's sticker. A company name, a phone number and a date, stuck to the cabinet. This is the best evidence a householder usually gets, because it dates the installation rather than the manufacture.
- A permit or inspection tag. A card or sticker from the local building department, often on the furnace cabinet or beside the panel, with a date and an inspector's initials. Same quality of evidence, and it also tells you the work was permitted.
- The serial number. Most manufacturers encode a manufacture date in the serial. The encoding differs by brand and by era, which is covered under Go deeper below. A manufacture date is a ceiling, not an install date: equipment can sit in a warehouse for a year.
- A date stamped on the unit itself. Some tanks and some outdoor units carry a date separately from the serial.
If none of them is legible, write unknown. Not "about 2010". Not a guess from how it looks. A record's value is that you can tell later what you knew A guess written down becomes a fact in six months, and a planning decision resting on it inherits an error nobody can see any more. What wears out and when has a specific procedure for an unknown age, and it depends on the row actually saying unknown.
Reading a serial number for a manufacture date
There is no standard. Each manufacturer encodes the date its own way, and most have changed the scheme at least once. Common patterns include four digits at the start giving week and year, a letter for the month followed by two digits for the year, and a letter for the year followed by a letter for the month. The practical method is to search the brand name, the word serial and the word date, read two sources that agree, and write down which scheme you used beside the result. A date you derived yourself is weaker evidence than an installer's sticker and should be recorded as derived.
What a seller's disclosure does and does not cover
A residential property disclosure is a statement by the seller about what they knew, on a form whose contents are set by state law. It is not an inspection and it is not a warranty, and the items it covers vary considerably between states. It is useful to a new owner as a list of questions rather than as a record: a disclosure that says the roof was replaced gives you a year to verify, not a year to write down. Whether your state requires one, and what it has to say, is a question for your state's real estate commission or consumer agency.
Finding permits through the building department
Most cities and counties keep a permit history by address, and many now publish it online. A permit record can date a roof, a water heater, a panel upgrade or an addition with more authority than anything in the house itself. It also shows work that was done without a permit, by its absence, which is a thing to know about rather than a thing to act on. Call the local building department and ask how to request the permit history for an address; the answer is free or close to it in most places.
What a paid home inspection costs and what it excludes
A home inspection is a visual, non-invasive examination carried out to a published standard of practice, usually over two to four hours. Inspectors work to the standard of their association, and every such standard excludes a long list: anything concealed, anything requiring disassembly, and typically pests, environmental hazards, code compliance and the future performance of any component. An inspection is worth buying when you are about to spend serious money on a decision the walk cannot settle, and it answers fewer questions than most people expect. It is not a substitute for the walk, and the walk is not a substitute for it.
4. The walk outside
Start at the street and go around the house once, slowly, in the same direction every time you do this. The order matters less than the repetition: a route you always walk the same way is a route where a change stands out.
- The roof, from the ground. Binoculars if you have them. You are looking for missing or lifted shingles, a sagging ridge line, anything growing on it, and the condition of the flashing where a chimney or a wall meets the roof. Nobody in this manual goes onto a roof.
- Gutters and downspouts. Count the downspouts and note where each one discharges. If plants are growing out of a gutter it is full. Keeping water out has the published figures for how many you need and how far the extensions should carry the water.
- The ground against the foundation. Does it slope away or toward? Is there a flower bed holding water against the wall? Are downspout extensions missing, or pointing into a bed? Is any wood touching soil?
- Hose bibs. How many, where, and does each one have its own shutoff inside.
- Vents and discharges. Where does the dryer vent come out, where do the bath fans come out, where does the water heater or furnace flue terminate. Is anything blocked by a shrub, a nest or a screen packed with lint.
- Meters. Water meter and electric meter: where they are and whether you can read them. The water meter is what makes the leak test in Keeping water out possible, so find it now.
- The outdoor equipment. The air conditioner or heat pump's outdoor unit, the propane tank, the well head, the septic lids if you know where they are. Note what is crowded by plants.
Write what you see, not what you conclude. "Downspout at the northwest corner ends at the wall" is an observation. "Need to fix the drainage" is a conclusion you are not ready to draw yet.
5. The walk inside
Inside, the walk is mostly about water, because water inside a house is almost always a sign of something rather than a thing in itself. Open every cabinet under every sink and put a hand on the floor of it.
- Under every sink. Wet, stained, soft, or a white crust on a fitting. A crust is a slow leak that has been evaporating; soft particleboard is a leak that has been there a while.
- Behind and beside every toilet. Rock it gently with both hands. Movement means the mounting is loose, which is a thing that gets worse.
- The water heater. At the base, in the drip pan if there is one, and at the fittings on top. Rust at the base of a tank is a different thing from a damp fitting, and Heating, cooling and hot water tells you which is which.
- The washing machine's hoses. Bulges, cracks, rust at the crimp. A burst supply hose can run until somebody comes home.
- The basement or crawl space. Walk the whole perimeter. Look for a line on the wall, efflorescence (a white powdery mineral deposit left where water evaporated out of masonry), rust at the bottom of anything metal, and anything stored on the floor that has gone soft.
- The ceilings. Under every bathroom, around every chimney, and in the room below the attic hatch. A ring that is dry today is still worth a row.
- The attic hatch. Open it and look with a flashlight from the opening. You are looking for daylight, for staining on the underside of the roof deck, and for how deep the insulation is. Air, moisture and insulation turns the depth into a number.
- The alarms. Count them, and note which rooms have none. Alarms, vents and tests has the published placement rule, and counting against it is a five-minute job that often finds a missing alarm.
6. What came with the house
Gather the paper into one box before you sort it: appliance manuals, warranty cards, the seller's disclosure, inspection reports, permits, service invoices, the survey, anything with a contractor's name on it. Then do one pass and copy four things out of it onto the systems sheet: install dates, model numbers, who did the work, and what they said they did.
The box is not the record. The sheet is the record, because the box gets moved, lent and lost, and because the sheet is the thing you can print. Convention Kansas State's homeowner curriculum sorts household tasks by how often they come round rather than by what they are, and the same instinct applies to paper: the useful question about a document is not what it is but what fact you need out of it.
7. What you do not open
This manual is specific about its own boundary, and the walk is where the boundary first comes up, because a householder with a screwdriver and an afternoon can get into real trouble in about ten minutes.
Not opened, here or anywhere in this manual: the electric panel's cover, a gas or propane line or connection, a sealed combustion cabinet, a flue or chimney, a refrigerant line, or a pressurized plumbing connection. For each of these the manual tells you what to look at, what a reading or a symptom means, and which trade or certification does the work. The who-to-call table names the trade for each, what to ask for in writing, and where a license is verified.
The reason to say this at the start rather than at the end is that competence feels like permission. Having read how a flue works, it is tempting to look inside one. CPSC's guidance is that the annual professional inspection of the heating system should cover the chimney and flue for blockages, corrosion, partial and complete disconnections and loose connections, which is a description of a technician's job rather than a checklist for a homeowner with a flashlight.
8. See it See it
Ray and Diane Okonkwo, a 1958 ranch outside Dayton, Ohio. 1,450 square feet, full basement, gutters, no fireplace, public water and sewer. Two hours on a Saturday produced this.
Known, read off a label or a sticker: the gas furnace and the central air conditioner both carry an installer's sticker dated March 2009. The water heater's data plate is legible and the plate's own date reads 2016. The main water shutoff is in the northwest corner of the basement, a gate valve, and it turned with some effort and did not weep afterward. The panel is a 100 amp service, labeled, in the basement stairwell.
Assumed, and the assumption is Ray's: the roof is "about fifteen years old", because the previous owner mentioned it at the closing. That is hearsay, and it goes on the sheet as roof: unknown, previous owner said approximately 2011 rather than as 2011. What would settle it is a permit record from the city building department or an invoice in the box of papers.
Still open, and who settles each: whether the basement's two downspout discharges are far enough from the wall (Ray can settle this himself with a tape measure and the drainage calculator); whether the stain on the joist under the upstairs bathroom is active or historic (Ray can settle this by marking its edge with a pencil and looking again after a week of use); whether the furnace's heat exchanger is sound at seventeen years old (only a heating technician's combustion inspection settles this, and it is the reason the annual service is on their list).
Their list came to twenty-two rows, unsorted. Not one of them was acted on that day. The three shutoffs were labeled and dated, which was the one thing that changed.
- University of Georgia Extension's home maintenance checklist (a five-page PDF): a room-by-room and area-by-area list of what to look at, organized by spring and fall. Useful as a prompt sheet to carry while you walk, and honest that frequencies vary with local climate and the manufacturer's recommendations.
- Kansas State Research and Extension's Essential Home Maintenance (publication S134C): a homeowner curriculum that sorts household tasks by frequency rather than by subject, with a home safety section.
- InterNACHI's estimated life expectancy chart: the trade-association table this manual reproduces, with the publisher named on every row, in the service life table.
9. Practice Practice
Minimum: the shutoffs and two systems rows, which is the Start here result. Time: about two hours for the minimum, a half day for the full walk. Materials: a notebook or a phone, a flashlight, a labeling method (tape and a marker is fine), binoculars if you own a pair, and a tape measure.
- Do the three shutoffs first and label them. Turn the water main off and on while nothing is wrong, and write what happened on the shutoffs sheet, including "turned stiffly" if it did.
- Walk outside once, in one direction, and write without concluding. One line per observation. Do not stop to fix anything.
- Walk inside, opening every under-sink cabinet. Put a hand on the floor of each one; a dry-looking cabinet can be damp at the back.
- Photograph and then transcribe every data plate you can reach safely. Type them onto the systems sheet rather than leaving them in the phone.
- Copy the unsorted list onto the ranked job list with the tier column left blank. Leaving it blank is the point; The priority rule fills it in.
Two longer exercises for a house you have time with. Request the permit history for your address from the building department and compare it against what you found, which often dates a roof or a panel upgrade for free. And walk the house a second time on a rainy day: where water goes is visible for about twenty minutes a year, and standing outside in it with a coat on is the cheapest diagnostic in this manual.
10. Your house Your house
11. Check your work Check your work
Criteria
- Could somebody who does not live in your house find the water main from what you wrote? Read the Where it is column aloud and ask whether it names a wall, a corner or a landmark rather than "the basement".
- Does every systems row have either a date or the word unknown, with no row carrying a guess dressed as a date?
- Is your list free of verbs like fix, replace and repair? Those are conclusions. The walk produces observations.
- Did you turn the water main, rather than only find it?
- Is there a row for anything you noticed and decided was fine? A dry stain, a stiff valve and a loose gutter are all rows.
Worked example
Checked against those criteria, the Okonkwos' walk passes on four and fails on one. Their water main row reads "basement, northwest corner, on the wall above the laundry tub, gate valve, turns clockwise, stiff", which somebody else could follow. Their roof row says unknown with the hearsay recorded beside it rather than as a date. They turned the valve. But four of their twenty-two rows say things like "regrade the north side", which is a conclusion with a solution already in it. Rewritten as "north side: ground slopes toward the wall for the first six feet, standing water after rain by the basement window", the row keeps the observation and leaves the decision for Keeping water out, which might reach a different answer.
Common mistakes
- Fixing during the walk. The first trip to the hardware store ends the walk. Carry the list, not the toolbox.
- Writing an estimated age as a date. See above; the word unknown is a finished answer.
- Skipping the valve test because the valve is obviously fine. A valve that looks fine and does not turn is the common case in an older house, and the test takes ninety seconds.
- Taking photographs instead of transcribing. A phone full of label photographs is not searchable, not printable, and not available to the person who is in the house when you are not.
- Opening the panel cover to read the labels. The labels you need are on the door, and the service size is stamped on the main breaker, which is visible with the cover on.
What is still unresolved
A walk finds what is visible. It does not find what is behind a wall, under a slab, inside a flue or inside a heat exchanger, and it is not a home inspection: an inspection is a visual examination to a published standard of practice, carried out by somebody who does it daily, and its own standards exclude concealed conditions too. What the walk also does not do is tell you what any of it means for your year, which is the subject of What wears out and when and then The priority rule. If something you found is actively wet right now, stop reading and turn the water off.